Binary number

system that represents numeric values using two symbols; 0 or 1
(Redirected from Binary numeral system)

The binary numeral system is a way to write numbers using only two digits: 0 and 1. These are used in computers as a series of "off" and "on" switches. In binary, each digit's place value is twice as much as that of the next digit to the right (since each digit holds two values). In decimal - the system that humans normally use - each digit holds ten values, and the place value increases by a power of ten (ones, tens, hundreds, etc.). The place value of the rightmost digit, in either case, is 1.

0 0000 0+0+0+0
1 0001 0+0+0+1
2 0010 0+0+2+0
3 0011 0+0+2+1
4 00100 0+0+4+0+0
5 00101 0+0+4+0+1
6 00110 0+0+4+2+0
7 00111 0+0+4+2+1
8 01000 0+8+0+0+0
9 01001 0+8+0+0+1
10 01010 0+8+0+2+0
11 01011 0+8+0+2+1
12 01100 0+8+4+0+0
13 01101 0+8+4+0+1
14 01110 0+8+4+2+0
15 01111 0+8+4+2+1
16 10000 16+0+0+0+0
17 10001 16+0+0+0+1
18 10010 16+0+0+2+0
19 10011 16+0+0+2+1
20 10100 16+0+4+0+0
21 10101 16+0+4+0+1
22 10110 16+0+4+2+0
23 10111 16+0+4+2+1
24 11000 16+8+0+0+0
25 11001 16+8+0+0+1
26 11010 16+8+0+2+0
27 11011 16+8+0+2+1
28 11100 16+8+4+0+0
29 11101 16+8+4+0+1
30 11110 16+8+4+2+0

Example: 10110011

  • The place value of the last 1 (rightmost position) is 1.
  • The place value of the 1 before that is 2.
  • The place value of the 0 before that is 4.
  • The place value of the 0 before that is 8.
  • The place value of the 1 before that is 16.
  • The place value of the 1 before that is 32.
  • The place value of the 0 before that is 64.
  • The place value of the 1 before that is 128.

Adding together all the place values that have 1s, it would be 1+2+16+32+128 = 179. For convenience, binary digits (bits, for short) are usually grouped together in two groups of 4 bits. This is 8 bits, or a byte, and is written using the hexadecimal numeral system. This would be shown as 1011 0011 = B3.

Binary arithmetic

change

Arithmetic is a way of adding together two or more binary numbers. There are four rules in binary arithmetic. They are:

0 + 0 = 0
1 + 0 = 1
1 + 1 = 10 (2)
1 + 1 + 1 = 11 (3)

This is because in binary there are only two digits; 0 and 1. Because of this, the number two and three have to be represented in some other way. This is how the binary value for three is calculated:

Column Decimal Value Binary
1 2 1
2 1 1

This shows that the binary value would be 11.

History

change
 
The binary numeral system, in a manuscript by Gottfried Wilhelm Leibniz, 1697
 
A page from „Explication de l’Arithmétique Binaire“, by Leibniz, 1703

Binary is a numbering system that is a series of 1s and 0s meaning (to the computers) on and off. It is base two and our number system (decimal) is base ten, where ten numerals are used rather than two.

In 1817 John Leslie (a Scottish mathematician) suggested that primitive societies may have evolved counting with objects (like pebbles) before they had even words to describe the total number of objects involved. The next step in the evolution of counting would have been the discovery that this pile of objects could be reduced into two piles of equal measures (leaving either 0 objects left over or just a remainder of 1). This remainder (odd = 1 or even = 0) would then be recorded and one of the piles removed whilst the second pile was then further divided into two sub piles. If you record the remainder left over after the original pile has been divided in two and continue repeating this process; of sub dividing one of the remaining piles into half and then removing one of those piles and continue by subdividing the remaining pile into two piles you will ultimately be left with just either 2 or 3 objects. If you record the remainder left over (odd = 1 or even = 0) at the end of each reduction you will eventually be left with a tally record of 1's and 0's which will be the binary representation of your original pile of objects. So instead of representing your original pile of objects with a repeating number or marks or tokens (which for large numbers could be quite long) you have reduced your pile of objects into more compact binary number. If you need to recover the original number of objects from this summarised binary number it is easy enough to do; by simply starting with the first tally mark and then doubling it and adding one if the next binary number contains a 1 and then continuing the process until the end of the binary number is reached. So binary counting may be both the oldest and the most modern method of counting.

Binary was invented by many people but the modern binary number system is credited to Gottfried Leibniz in 1679, a German mathematician. Binary has been used in nearly everything electronic; from calculators to supercomputers. Machine code is binary digits.

change


Translation

change

You can translate binary to normal numbers using